EN

DC motor analysis

Speed, torque, starting, speed control and efficiency with separate, shunt or series excitation

1. Fundamental equations

As it rotates in the field of the poles, the armature generates a back EMF \(E\) proportional to the flux and the speed; the armature current, in that same field, produces a torque proportional to the flux and the current. With the machine constant grouped as \(k\Phi\) (in V·s/rad, which is the same as N·m/A):

\[ E = k\Phi\,\Omega \]\[ T = k\Phi\,I_a \]\[ U = E + R_a I_a + \Delta U_{esc} \]
Armature circuit: applied voltage, armature resistance, brush drop and back EMF.

Solving for the speed gives the equation that governs the whole behaviour of the motor:

\[ \Omega = \frac{U - \Delta U_{esc} - R_a I_a}{k\Phi} \qquad n = \frac{60}{2\pi}\,\Omega \]

2. Types of excitation

ExcitationFluxTorque-speed curveTypical use
SeparateConstant, from a separate sourceAlmost horizontal line: speed drops little with loadDrives controlled by armature voltage
ShuntConstant if the voltage isSame as separate excitationMachine tools, fans
SeriesProportional to the currentHyperbola: high torque at low speed; runs away at no loadTraction, cranes, universal motors
CompoundSum of bothIntermediateLoads with torque shocks

In the series motor the flux grows with the current, so torque grows with its square (\(T \propto I^2\)) as long as the magnetic circuit does not saturate. Without load the current is small, so is the flux, and the speed rises without limit: a series motor must never be started or run without load, nor coupled with belts that could slip off.

3. Speed control

4. Starting

At standstill \(E = 0\) and the only limit on the current is the armature resistance, which is very small. To keep the current drawn at start below \(k\) times rated current, a rheostat is inserted:

\[ I_{a,arr} = \frac{U - \Delta U_{esc}}{R_a} \]\[ R_{arr} = \frac{U - \Delta U_{esc}}{k\,I_{n} - I_{exc}} - R_a \]

In the series motor the resistance of the field winding, which is in the same circuit, is added as well.

The rheostat is cut out in steps as the motor accelerates and the back EMF builds up.

5. Power balance

\[ P_1 = U\,I \]\[ P_{Cu} = R_a I_a^2 \]\[ P_{esc} = \Delta U_{esc}\,I_a \]\[ P_{exc} = \frac{U^2}{R_{exc}}\ \text{(derivación)} \]
\[ P_{mi} = E\,I_a \]\[ P_u = P_{mi} - P_{rot} \]\[ \eta = \frac{P_u}{P_1} \]

\(P_{rot}\) groups the mechanical and iron losses. The calculator derives them from the nameplate data (the difference between rated internal power and output power) and treats them as a constant loss torque.

6. Calculator

Motor (nameplate data)
V
A
rpm
kW
Ω
Includes interpoles and compensating winding
V
Usually taken as 2 V (1 V per brush)
Ω
Operating point
V
% of rated
Ω
% of rated
× In

A linear magnetic circuit (no saturation) is assumed: in shunt motors the flux is proportional to the applied voltage and in series motors to the current.

Derived rated data

Operating point

Starting

Speed-torque curve

Example: 10 kW, 220 V, 52 A, 1500 rpm shunt motor

Ra = 0.25 Ω, Rexc = 110 Ω and a 2 V brush drop.

\[ I_{exc} = \frac{220}{110} = 2\ \text{A} \qquad I_a = 52 - 2 = 50\ \text{A} \qquad E = 220 - 2 - 0.25 \cdot 50 = 205.5\ \text{V} \]
\[ k\Phi = \frac{205.5}{2\pi \cdot 1500/60} = 1.308\ \text{V}\cdot\text{s/rad} \qquad P_{rot} = 205.5 \cdot 50 - 10\,000 = 275\ \text{W} \]

With direct-on-line starting \((220 - 2)/0.25 = 872\) A would flow, almost 17 times rated current. To keep the current drawn below 2·In = 104 A, the armature may take 102 A (the other 2 A are for the field), which calls for a rheostat of \(218/102 - 0.25 = 1.89\ \Omega\).

Related: DC machine fundamentals · H-bridge for DC motors · induction motor analysis