EN

Three-phase induction motor analysis

Equivalent circuit, power balance, torque and efficiency, torque-speed curve and tests

1. The equivalent circuit

An induction motor behaves like a transformer whose secondary (the rotor) rotates. With everything referred to the stator, each phase is represented by the circuit below. The parameters are those of the equivalent star: if the motor is delta-connected, the phase impedances are divided by 3.

Per-phase equivalent circuit of the induction motor, referred to the stator.
\[ n_s = \frac{60\,f}{p} \]\[ s = \frac{n_s - n}{n_s} \]\[ \Omega_s = \frac{2\pi\,n_s}{60} \]

\(p\) is the number of pole pairs and \(s\) the slip: 0 at synchronous speed, 1 with the rotor at standstill, normally between 1 % and 6 % at full load.

2. Power balance

\[ P_1 = \sqrt3\,U\,I\cos\varphi \]\[ P_{a} = P_1 - P_{Cu1} - P_{Fe} = 3\,I_2'^2\,\frac{R_2'}{s} \]
\[ P_{Cu2} = s\,P_a \]\[ P_{mi} = (1-s)\,P_a \]\[ P_u = P_{mi} - P_{mec} \]\[ \eta = \frac{P_u}{P_1} \]

The power crossing the air gap, \(P_a\), is always split in the same proportion: a fraction \(s\) is lost in the rotor copper and the rest is converted into mechanical power. That is why a motor with a lot of slip can never have a good efficiency. The electromagnetic torque is \(T = P_a / \Omega_s\) and the output torque \(T_u = P_u / \Omega\).

3. Torque-speed curve

Replacing the supply with its Thévenin equivalent as seen from the rotor (\(V_{th}\), \(R_{th} + jX_{th}\)):

\[ T = \frac{3\,V_{th}^2\,R_2'/s}{\Omega_s\left[\left(R_{th} + R_2'/s\right)^2 + \left(X_{th} + X_2'\right)^2\right]} \]
\[ s_{T\max} = \frac{R_2'}{\sqrt{R_{th}^2 + (X_{th} + X_2')^2}} \]\[ T_{\max} = \frac{3\,V_{th}^2}{2\,\Omega_s\left[R_{th} + \sqrt{R_{th}^2 + (X_{th}+X_2')^2}\right]} \]

4. Operating point calculator

Supply and motor
V
Hz
W
Per-phase parameters (equivalent star)
Ω
Ω
Ω
Ω
Ω
Ω
Operating point

Operating point

Power balance

Starting and breakdown torque

Torque and current curves

5. Obtaining the parameters: tests

The circuit parameters are obtained from three simple measurements on the test bench:

\[ R_{cc} = \frac{P_{cc}}{3\,I_{cc}^2} \]\[ Z_{cc} = \frac{U_{cc}}{\sqrt3\,I_{cc}} \]\[ X_{cc} = \sqrt{Z_{cc}^2 - R_{cc}^2} \]\[ R_2' = R_{cc} - R_1 \]
\[ X_0 \approx \sqrt{\left(\frac{U_0}{\sqrt3\,I_0}\right)^2 - \left(\frac{P_0}{3 I_0^2}\right)^2} \]\[ X_\mu = X_0 - X_1 \]\[ P_{Fe} + P_{mec} = P_0 - 3\,I_0^2 R_1 \]

How \(X_{cc}\) is split between stator and rotor depends on the cage design (NEMA classification):

Design\(X_1\)\(X_2'\)Characteristics
A and D, wound rotor50 %50 %Normal starting torque (A) or very high with large slip (D)
B40 %60 %The general-purpose motor
C30 %70 %Double cage: high starting torque

Mechanical losses can only be separated from iron losses by repeating the no-load test at several voltages; if they are unknown, they are typically around 1 % to 2 % of rated power in medium-sized motors.

Test results
Ω
V
A
W
V
A
W
W
Example: 4-pole motor at 400 V, 50 Hz

With the calculator's default parameters and a slip of 3 %: \(n_s = 1500\) rpm and \(n = 1455\) rpm.

\[ \frac{R_2'}{s} = \frac{0.45}{0.03} = 15\ \Omega \qquad \overline{Z} = R_1 + jX_1 + \left(R_{Fe} \parallel jX_\mu\right) \parallel \left(\frac{R_2'}{s} + jX_2'\right) \approx 11.6 + j7.4\ \Omega \]
\[ I = \frac{400/\sqrt3}{13.7} \approx 16.8\ \text{A} \qquad \cos\varphi \approx 0.84 \qquad P_1 \approx 9.8\ \text{kW} \]

The calculator completes the balance: about 8.6 kW output, 56.6 N·m and an efficiency close to 88 %. The breakdown torque, about 164 N·m, is reached at around 1220 rpm.

Related: induction motor fundamentals · star-delta starting · transformer analysis