EN

Dahlander motor

Two speeds in a 1:2 ratio with a single winding

What a Dahlander motor is

It is a three-phase induction motor with a single winding that can run with two numbers of poles, one twice the other, and therefore at two speeds in a 1:2 ratio. It is named after Robert Dahlander, who patented the connection at the end of the 19th century. Each phase is split into two halves with a centre tap brought out to the terminal box; by changing how those halves are connected, the motor switches from one pole number to the other.

Poles (low / high)Synchronous speed at 50 HzAt 60 Hz
4 / 21500 / 3000 rpm1800 / 3600 rpm
8 / 4750 / 1500 rpm900 / 1800 rpm
12 / 6500 / 1000 rpm600 / 1200 rpm

Actual speeds are slightly lower because of slip.

Why the number of poles changes

Each phase has as many coil groups as there are poles at high speed. At high speed the current flows through the groups in alternating directions: one creates a north pole, the next a south pole, and so on; it is a whole-coiled winding. At low speed the current is reversed in half of the groups, so that they all create poles of the same polarity; between every two groups a pole of opposite polarity then appears, where the flux closes (consequent poles). The number of poles doubles and the speed halves.

That half-phase reversal is exactly what the terminal box does when changing from one connection to the other, without touching the winding.

The connections

1U1V1W2U2V2WL1L2L3ΔL12UL22VL32W1U·1V·1WYY
Left: low speed in delta, with the supply on 1U-1V-1W and the centre taps 2U-2V-2W left open. Right: high speed in double star, with the supply on 2U-2V-2W and 1U-1V-1W joined together.

Depending on how the half-phases are connected at low speed, there are two types of Dahlander motor, which behave differently:

TypeLow speedHigh speedTorquePower ratio (indicative)Applications
Δ / YYDeltaDouble starRoughly constantHigh speed gives 1.4 to 1.8 times the low-speed powerMachine tools, conveyors, hoisting
Y / YYStarDouble starVariable: much lower at low speedLow speed gives a quarter to a sixth of the high-speed powerFans and centrifugal pumps

The Y/YY type suits quadratic-torque loads: a fan at half speed needs only a quarter of the torque and an eighth of the power. There is also the YY/Δ connection, with constant power, which is uncommon. From the outside all three types are handled in the same way: the difference lies in the internal connections, and the nameplate shows it (for example "Δ/YY" or "Y/YY") together with the power and current for each speed.

Terminal box and switching

SpeedSupply L1-L2-L3 toLinksFree terminals
Low1U - 1V - 1WNone2U - 2V - 2W (insulated)
High2U - 2V - 2W1U + 1V + 1W joinedNone

With contactors, switching needs three of them:

KM1 must be interlocked with KM2 and KM3, electrically and mechanically: if KM3 closed together with KM1, it would short-circuit the supply. As each speed has its own rated current, two overload relays are used, one at the output of KM1 and another at the output of KM2, each set to the nameplate current of its speed.

Speed change and direction of rotation

The Dahlander winding

It is a normal three-phase winding, almost always double-layer, with two particular features. First, the number of groups: each phase has as many groups as there are poles at high speed, divided into two equal halves with the centre tap. Second, the coil pitch: a full pitch for the high speed would be twice the pole pitch of the low speed, so an intermediate pitch is chosen that works acceptably at both. The winding factor is not optimal at either speed, which is why a Dahlander motor performs slightly worse than a single-speed motor of the same size.

When rewinding, the pitch, the number of groups, the order of the halves and the internal connection (Δ or Y at low speed) must be kept, and the six leads must be clearly marked. Before assembly it is advisable to check the resistance of each half-phase and run a no-load test at both speeds.

Advantages and limitations

Related guides