EN

Reflectance factors

Reflectance of colours and materials, recommended values and their effect on lighting

When light reaches a surface, part is reflected, part is absorbed and, if the material is translucent, part passes through. The reflectance factor or reflectance \(\rho\) is the fraction of the flux that is reflected:

\[ \rho = \frac{\Phi_{reflected}}{\Phi_{incident}} \qquad \rho + \alpha + \tau = 1 \]

where \(\alpha\) is the absorptance and \(\tau\) the transmittance. Indoors, surfaces reflect light over and over again, so their colours have a big influence on the final lux: the same room with white walls may need 20–30 % fewer luminaires than with dark walls.

Table of reflectance factors

Colour or materialReflectance
Paints and colours (matt finish)
White, new plaster0.80–0.85
Ivory, cream0.65–0.75
Light yellow0.60–0.70
Beige, sand0.50–0.65
Light grey0.45–0.60
Light green0.45–0.60
Light blue0.40–0.55
Medium grey0.25–0.40
Red0.15–0.25
Dark green, dark blue0.05–0.15
Black0.03–0.05
Building materials
Light exposed concrete0.25–0.40
Red brick0.10–0.20
Light wood (beech, pine, maple)0.30–0.50
Dark wood (walnut, dark oak)0.10–0.20
Light tiles or terrazzo0.30–0.50
Dark carpet0.05–0.10
Clear glass0.08–0.10
Metals and outdoors
Bright anodised aluminium, mirror0.80–0.95 (specular)
Stainless steel0.55–0.65
Asphalt0.07–0.10
Grass0.10–0.20
Fresh snow0.75–0.90

Approximate values. Paint manufacturers state the LRV (Light Reflectance Value) of each colour, which is the reflectance in %.

Estimate the reflectance of a colour

Choose a colour similar to that of the surface. The value is calculated from the relative luminance of the colour in sRGB, which is the same quantity the LRV measures; it is an estimate, because the colour on screen is never exactly that of the paint.

Colour

Recommended values

The EN 12464-1 standard recommends these ranges for the main surfaces of an interior:

SurfaceRecommended reflectanceWhy
Ceiling0.70–0.90Returns light downwards and avoids the "cave" effect; essential with indirect lighting.
Walls0.50–0.80Add reflected light and luminance to the field of view.
Floor0.20–0.40A floor that is too light causes reflections; a very dark one absorbs a lot of light.
Work surfaces0.20–0.60Avoid excessive contrast with paper or screen.

Besides saving energy, surfaces with balanced reflectances reduce the contrast between the luminaires and their surroundings, and with it the glare. A dark ceiling with bright luminaires is much more glaring than a white one with the same luminaires.

Average reflectance of a room

To estimate the light arriving by reflection, the average reflectance of the room is used, weighted by the area of each surface. Light is reflected many times before being absorbed, and the total flux that ends up reaching the surfaces is the direct flux multiplied by \(1/(1-\bar\rho)\):

\[ \bar\rho = \frac{\sum \rho_i\, S_i}{\sum S_i} \qquad E_{ind} = \frac{\Phi\,\bar\rho}{S_{tot}\,(1-\bar\rho)} \]
Room
m
m
m
%
Reflectances
%
%
%
lm

How they enter the lighting calculation

Types of reflection

The type of reflection also matters for the luminance we see: on a diffuse surface, \(L = \rho\,E/\pi\). A white sheet of paper (\(\rho = 0.8\)) at 500 lx has a luminance of about 127 cd/m².

Related: lighting calculation, point-by-point method, energy efficiency (VEEI) and colour temperature.