EN

Pt100 calculator

Resistance thermometers: ohms ↔ temperature according to IEC 60751, tolerances, lead error and tables

Conversion between resistance and temperature

Sensor
Temperature → resistance
°C
Resistance → temperature
Ω

Lead wire error and self-heating

Calculates how much the connecting wires and the measuring current distort the reading, at the temperature entered above.

Installation
m
mm²
mA
mW/°C

Resistance table

°C
°C

What a resistance thermometer is

A resistance thermometer (RTD, Resistance Temperature Detector) relies on the fact that the resistance of a pure metal increases with temperature. Platinum is the reference material: it is stable, almost linear and does not oxidise. Pt100 means "platinum, 100 Ω at 0 °C"; the Pt1000 is 1000 Ω, gives ten times more signal and is less sensitive to lead resistance.

The resistance–temperature relationship of industrial platinum is defined by IEC 60751 with the Callendar-Van Dusen equation:

\[ R_t = R_0\left[1 + A\,t + B\,t^2 + C\,(t - 100)\,t^3\right] \quad (-200 \le t < 0\ °C) \qquad R_t = R_0\left(1 + A\,t + B\,t^2\right) \quad (0 \le t \le 850\ °C) \]

with \(A = 3.9083\cdot10^{-3}\ °C^{-1}\), \(B = -5.775\cdot10^{-7}\ °C^{-2}\) and \(C = -4.183\cdot10^{-12}\ °C^{-4}\). The mean coefficient between 0 and 100 °C, \(\alpha = \frac{R_{100} - R_0}{100\,R_0} = 0.00385\ °C^{-1}\), identifies this platinum. Some old American sensors use α = 0.00392: their tables are different and must not be mixed up.

MaterialUsual rangeSpecial rangeCharacteristics
Platinum (Pt100, Pt1000)−200 to 600 °Cup to 850 °CStable, interchangeable and standardised. The most widely used.
Nickel (Ni100, Ni1000)−60 to 180 °Cup to 350 °CMore sensitive and cheaper, not very linear. HVAC.
Copper (Cu10, Cu100)−100 to 100 °Cup to 150 °CVery linear but low resistance. Motor and transformer windings.
NTC/PTC thermistors−100 to 200 °C–Very sensitive and very non-linear; thermal and electronic protection.

Tolerance classes (IEC 60751)

ClassToleranceRange, wire-wound elementRange, film elementAt 0 °C (Pt100)
AA (1/3 DIN)±(0.10 + 0.0017·|t|) °C−50 to 250 °C0 to 150 °C±0.10 °C · ±0.04 Ω
A±(0.15 + 0.002·|t|) °C−100 to 450 °C−30 to 300 °C±0.15 °C · ±0.06 Ω
B±(0.30 + 0.005·|t|) °C−196 to 600 °C−50 to 500 °C±0.30 °C · ±0.12 Ω
C±(0.6 + 0.01·|t|) °C−196 to 600 °C−50 to 600 °C±0.6 °C · ±0.23 Ω

The calculator applies the ranges of wire-wound elements. Class AA used to be called "1/3 DIN"; sensors of 1/5 and 1/10 DIN, outside the standard, are also sold.

2, 3 and 4-wire connections

2 wires 3 wires 4 wires 4 wires with loop red · white red · red · white red · red · white · white red · white + blues
Wire colours according to IEC 60751: wires of the same colour come from the same end of the element.

Self-heating

To measure the resistance a current has to flow, which dissipates \(P = I^2 R\) and heats the sensor above the medium. The error is \(\Delta t = P / \delta\), where \(\delta\) is the dissipation constant (mW/°C) given by the manufacturer: a few mW/°C in still air and considerably more in a stirred liquid. With 1 mA in a Pt100 the power is 0.1 mW and the error is usually negligible; with 5 mA it is already 25 times greater.

Thermocouple or resistance thermometer

CriterionThermocouplePt100
Accuracy and stabilityMedium (±1.5 to ±2.5 °C)High (±0.1 to ±0.3 °C at 0 °C)
Range−200 to 1800 °C−200 to 850 °C
Size and speedCan be very thin and fastLarger element, slower response
Vibration resistanceVery goodFair
WiringExtension or compensating cableOrdinary copper cable
Cold junctionNeeds compensationNot applicable
CostLow2 to 3 times higher

Quick checks

Related: thermocouple calculator, thermocouple guide, 4–20 mA transmitters and Ohm's law.