Six problems solved step by step, from the simplest to dependent sources and AC
Six problems in order of difficulty. They all follow the same method: remove the load, find the open-circuit voltage \(V_{Th}\), find the equivalent resistance (or impedance) \(R_{Th}\) and reconnect the load. If you need to review the theory, it is in Thévenin's and Norton's theorems, and you can check the DC results with the circuit analyser.
Find the current and power in a load \(R_L = 6\ \Omega\) connected between A and B.
With A–B open no current flows to the load, so \(V_{Th}\) is the divider voltage. With the source short-circuited, R1 and R2 are in parallel:
Norton equivalent: \(I_N = V_{Th}/R_{Th} = 4\ \text{A}\) in parallel with 2 Ω.
Two branches in parallel feed terminals A–B. Find the current in a 4 Ω load.
With A–B open, the two branches form a single mesh. The current flowing from branch 1 to branch 2 is:
(This is the same result given by Millman's theorem.) With both sources turned off, 4 Ω and 2 Ω are in parallel:
Find the Thévenin equivalent, the current in a 5 Ω load and the load that absorbs maximum power.
With A–B open no current flows through R2, so all the source current goes through R1. With the current source turned off (open circuit), R1 and R2 are in series:
Maximum power: with \(R_L = R_{Th} = 15\ \Omega\), \(P_{max} = \dfrac{V_{Th}^2}{4 R_{Th}} = \dfrac{400}{60} = 6.67\ \text{W}\).
The controlled current source injects a current of \(0.25 \cdot V_A\) into node A (in amperes, with \(V_A\) in volts). Find the Thévenin equivalent.
Open-circuit voltage. Node equation at A with the terminals open (currents in = currents out):
Short-circuit current. When A is joined to B, \(V_A = 0\): the dependent source contributes nothing and no current flows through R2.
Check with a test source. Turning off only the 10 V source and applying \(V_p\) at A: \(I_p = V_p/2 + V_p/4 - 0.25\,V_p = 0.5\,V_p\), that is, \(R_{Th} = 2\ \Omega\). ✓
Typical mistake: also turning off the dependent source. That would give \(R_{Th} = 2 \parallel 4 = 1.33\ \Omega\), which is wrong.
A 50 Ω galvanometer is connected between A and B. What current flows through it?
Without the galvanometer, each side of the bridge is an independent voltage divider:
With the source short-circuited, two parallel pairs in series are seen from A and B:
The bridge would be balanced (\(I_G = 0\)) if \(R_1/R_2 = R_3/R_4\).
A \(100\angle 0^\circ\) V source, a 10 Ω resistor and a capacitor with a reactance of 10 Ω. Find the Thévenin equivalent and the load that receives maximum power.
The capacitor is \(\overline{Z}_C = -j10\ \Omega\). The voltage divider is applied with impedances:
Power is maximum with the conjugate load, \(\overline{Z}_L = 5 + j5\ \Omega\):
With a purely resistive 10 Ω load, on the other hand: \(\overline{I} = \dfrac{50 - j50}{15 - j5} = 4 - j2\ \text{A}\), \(|I| = 4.47\ \text{A}\) and \(P = 4.47^2 \cdot 10 = 200\ \text{W}\).
Related: Thévenin and Norton theory · Kirchhoff's laws · Millman's theorem